风机使用说明书-高温风机 防腐风机 无泄漏风机
您好,欢迎访问高温风机 防腐风机 无泄漏风机!
泰州市天城环保设备制造有限公司
产品分类

风机使用说明书

当前位置:首页 > 新闻中心 > 公司新闻
详细信息

使用前请仔细阅读本说明书

Please  read  before  usinig  this  manual

 

 

风机使用说明书

运行、维护手册

FAN  INSTRUCTIONS

Operation and maintenance manual

 

 

 

 

 

 

 

 

 

 

 

一、           风机的安装与使用

Installation  and   Operations

(一)   安装

1、  安装前首先检查风机各部件是否齐全,对蜗壳、叶轮、主轴等主要部件应检查是否出现由于运输而出现变形和损坏,否则,应予修复后方可安装。

2、  风机运行前应检查各部件螺栓是否拧紧,如出现松动,必须拧紧各部位的螺栓;校正进风口与叶轮之间的间隙,主轴保持水平和中心位置。

3、  检查即机壳内是否有掉入或遗留的工具和杂物,否则应予以清除。

4、  安装风机时,应充分利用千分表和塞尺,测量风机主轴和电机轴同心度及联轴器两端面的平行度,否则予以校正。两轴同心度允许误差为0.05mm,联轴器两端部平行度允差为0.1mm

5、  风机安装完毕后,用手或杠杆拨动叶轮,检查是否有过紧或碰撞现象。在无过紧或碰撞现象的 情况下方可进行试运转。

6、  电机安装后,应安装带轮护罩或联轴器护罩,如进气口处不接进气管道时,也需加添防护网(一般用户自备)。

7、  安装进风口管道时,可以直接利用风机进风口的螺栓孔进行连接。但通风管道的重量不应加在机壳上。

8、  风机的其他部件,必须严格按图纸要求进行安装。

9、  主轴转数(n)变化后,其风机的流量Q、全压H、轴功率N变化如下:

Q1/Q2=n1/n2  H1/H2=n1/n22   N1/N2=n1/n23

10、              风机所消耗的功率,是指在额定工况条件下,虽然有一定的富余量,但是,由于工况条件的故意改变而导致电机功率增大,例:进、风口全开时,风机空运转会使风机消耗功率增大而烧坏电机。在风机试运行时,应注意电机的电流是否会出现超流现象,否则,应查明原因方可运行。

(Ⅰ)Installation

1Before mounting,first of all,check over all parts of fan,especially  main parts such as worm gear, impeller and shaft for transportation deformation and damages,If something is wrong,please repair it before mounting.

2Check up bolts of all parts befor the fans are operatcd,Please connect all bolts if they become flexible,and check the distance between intel and impellet to make the shaft keeping horizontal and center location.

3Be sure that remains such as tools,cluster of cloth and left in the fan casing.

4Keep the nonhomcentricity of fan’s shaft and motor’s shaft within 0.05mm and the unparallelism of two ends of the coupling within 0.1mm for  fans.

5Turn the rotator with hand or lever to feel whether it is too tight or impacted after mounting .Make the fan operate under normal condition.

6Mount belt guard and coupling guard after the motor is mounted ,also mount the guard in the intel if the intel is not connected by a duct.

7Couple allowably intel duct with bolts of fan’s inlet.Howere,the weight of duct must not be able to load on the fan casing.

8All other parts of fans must be mounted as per design drawings stringently.

9Fans’ airflow(Q),total pressure(H)and shaft asorbed power(N) will have the following changes when impeller speed of rotation(n) changes:

Q1/Q2=n1/n2  H1/H2=n1/n22   N1/N2=n1/n23

Therefore , it is not allowable to increase the impeller speed of rotation without the capacity of motor changing .Otherwise , it would result in motor’s overload and being damaged.

10The motor powe is not selected for free discharge but for some special condition,Although the motor power has surplusage in specified opcration condition,it will increase because of the changing of condition intertionally.For example,fan run frelly without any resistance will make the power increase to damage the motor when both opening the inleft an outlet .While the fans are opetating,pay attention to the absorbed current of motor whether to exceed the specified volume,otherwise , the reasons have to be found out .

 

()、风机运行中的故障及产生原因

故障名称

产生原因

轴承箱振动剧烈

1、机壳或进风口与叶轮摩擦

2、基础的刚度不牢

3、叶轮铆钉松动或叶轮前后盘变形

4、叶轮轴盘与轴松动,联轴器螺栓松动

5、机壳与支架、轴承箱与支架、轴承箱盖与轴承座等联接螺栓松动

6、风机进出气管道安装不良

7、转子失衡

轴承温升过高

1、轴承箱振动剧烈

2、润滑油质量不良、变质、含有灰尘、砂粒、污垢等杂质

3、轴承箱盖与座联接螺栓的预紧力过大或过小

4、轴与滚动轴承安装歪斜,前后两轴承不同心

5、滚动轴承损坏或轴弯曲

电机电流过大

和温升过高

1、开机时通风管道内闸门或节流阀未关闭、风管漏气等

2、风机流量超过规定值

3、风机输送气体密度过大

4、电机输入电压过低或电源单相断电

5、受轴承箱剧烈振动的影响

6、受并联风机恶化或发生故障的影响

胶带跳动和胶带下滑

两皮带轮位置没有找正,彼此不在同一截面上,带轮距离太近或胶带太长,风机运转时剧烈振动。

(Ⅱ)Following table presents some probable causes

 

Malfunctions

Probable    causes

Vibration   of bearing-box

1Fan   house or inlet with impeller

2The   stiffness or strength of foundati 88 88on is not big enough.

3Impeller   rivets become loose or impeller front and behind plate is deformed.

4Between   impeller shaft installing sleeve and shaft has loose contact,coupling bolts   come loose.

5Connection   becomes loose between wheel disc and shaft ,or fan casing and house frame .   or bearing-box and support ,or bearing-cap and house frame , or bearing-box   and support , or bearing-cap and shaft supports,etc.

6Duct   vibration effected by incorrect mounting of intel and outlet ducts.

7Rotator   is out of balance.

Overheat   of bearing

1Vibration   of bearing-box.

2Lubricant   grease is in bad quality or deterioratedor blocked too much ,or contains dust   ,sticky sand other dirty.

3The   tension of connection bolts bearing cap and its support is too big.

4Driven  shaft is mounted unnormally to motor   shaft.The front and back bearings are not concentric.

5Roll-bearing   is damaged

Overcurrent   and overheat of motor

1Inlet   valve or throttle valve is notclosed at start while the fans are operated.

2Airflow   surpasses the rated volume.

3The   density of the conveying gas is too high.

4Input   voltage of motor is too low or one phase of electricity is broken down .

5Effected   by the vibration of bearing-box.

6Connected   fans run in bad state even with failure.

Run-away   of belt and slipping of belt

Position of pulleys are not setting ,each   other is not in the same plane.Span of pulleys. Too shaort or too long   .Vibration with fan rotation.

 

(三)、维护保养

(Ⅲ)Maintenance

1、风机维护工作制度

①风机运行时,必须定期检查,是否出现电流过载和发出异常声音,否则,应予修复后方可运转。

②风机长期运行,一年内应予维护保养,电机轴承和传动件的轴承箱应添加润油脂,否则会损坏传动件或电机。

③如风机输送的气体带有尘埃,必须定期清除风机及输气管道内的灰尘、污垢等杂质,防止锈蚀和堵塞风道。

④风机修复时,应切断电源,以保证安全。

2、风机运转时如出现下列不正常情况之一的,必须停机修复:

发现电流过大;风机运行时出现异常的声音;胶带过于松动;发生剧烈振动;电机温升过高。

1Fan maintenance system

When the fan is operated ,it has to be examined regulary whether the absorbed current of motor is overloaded and there is unusual sound.Otherewise ,the fans may be runned until rpairing it.

If the fan is operated continuously ,it have to be maintenance in one year ,the motor shaft and the casing of the bearing of drive parts have to be get more gread against damaging driven parts or motor.

If there is any foringen substsmces in the conveying gas ,clean up dust and dirty in the fan and ducts regulary to prevent any rust or blocking ducts.

Being repaired ,the fans have to be cut of the electricity supply for safely.

2.There are the following abnormal conditions while the fan is running,it has to be stopped and repaired:

Overcurrent of motor ;uusual sound of the running fas;the lossen belt;vibration of bearing-box;the overheat of motor.


推荐新闻
 
QQ在线咨询